CallFree EstimateSchedule Service

Furnace Tune-Ups & Heating Maintenance in Maple Grove, MN

A fall furnace tune-up is the cheapest insurance a Minnesota homeowner can buy. Heating & Cooling Two inspects, cleans, and safety-tests furnaces and boilers across Maple Grove and the Twin Cities metro — every make and model. Family-owned since 1980. Call 763-428-3677.

Family-owned since 1980

Three generations of Twin Cities neighbors keeping homes and businesses comfortable.

NATE-certified technicians

Factory-trained, background-checked techs who explain the work before they start.

Bryant Factory Authorized Dealer

Top-tier equipment, factory warranties and rebates you can only get from an authorized dealer.

The visit

What's included in a furnace tune-up

Every visit is covered for members of our maintenance plans, which include two visits a year plus discounted repairs.

  • Replace Air Filter (Optional)
  • Flush Drain Lines & Condensate Trap
  • Inspect Blower Components
  • Inspect Carbon Monoxide Levels
  • Inspect Heat Exchanger & Burners
  • Inspect Electrical Connections & Wiring
  • Inspect & Test Safety Controls
  • Inspect Thermostat Operation
  • Inspect Pilot Operation
  • Check for Proper Venting
  • Check Amp Draw / Motors
  • Monitor Electrical Currents
  • Monitor Heating Cycles
  • Monitor Flue Draft Operation
  • Adjust Gas Pressure
  • Adjust Air Flow for Proper Temperature
  • Lubricate All Moving Parts
  • Inspect Overall Operation

Safety first

It's also your annual carbon monoxide check

This visit isn't just about preventing breakdowns — it's the annual carbon monoxide check. A cracked heat exchanger or failing burner can put CO into your home without any obvious symptoms. Our technicians test for it on every tune-up. That's been the standard here since 1980.

Why it matters

Skipped maintenance is the number one cause of the no-heat calls we take during the first hard freeze — and most HVAC manufacturers require documented annual maintenance to keep your warranty valid. Two-visit maintenance plan members get the fall furnace visit covered automatically, plus discounted repairs.

Maintenance PlansBoilers

Between visits

What you can do yourself

A tune-up once a year handles the parts that need tools and training. These simple habits keep the furnace healthy the rest of the winter:

  • Check a 1-inch filter every month during heating season and change it when it looks gray. Thicker 4- or 5-inch media filters usually last six months to a year.
  • Keep supply registers open and return grilles clear of furniture, rugs and curtains.
  • After every snowstorm, check the white PVC intake and exhaust pipes outside a high-efficiency furnace. Snow or ice on them can shut the furnace down.
  • Keep the area around the furnace clear. Don't store paint, gas cans or boxes against it.
  • Test your carbon monoxide alarms monthly. Minnesota requires one within 10 feet of every sleeping room.
  • If your furnace has a whole-house humidifier, replace the water panel each fall.

Warning signs

Signs your furnace needs attention now

Don't wait for the fall visit if you notice any of these. Most are early warnings of a part that's about to fail:

  • Short cycling: the furnace starts and stops every few minutes
  • New noises, like banging, squealing or rattling, when it starts or runs
  • A blinking error light on the control board
  • Rooms that won't reach the thermostat setting
  • Water around the furnace or a gurgling drain
  • A yellow or flickering burner flame instead of a steady blue one
  • Gas bills climbing with no change in the weather
  • A carbon monoxide alarm going off. Get everyone outside and call 911 first.

Timing

Why fall is the right time

The best time for a furnace tune-up in the Twin Cities is September through October, before the first hard freeze. That gives you time to fix anything we find while it's still mild outside, and it gets you on the schedule before no-heat calls fill it. If you missed fall, a mid-winter tune-up is still worth it. A furnace that runs six or seven months a year here does a lot of work between visits.

If you have a boiler, the fall visit covers the burner, pressure, relief valve, pumps and venting. If you have a heat pump with a furnace backup, we also check the defrost cycle and the switch to backup heat.

Maintenance plans

Silver, Gold and Platinum plans

Our maintenance plans bundle the fall furnace visit and the spring AC visit into one plan, so you don't have to remember to call. Members also get discounted repairs. See the maintenance plans page for what each level includes, and check current specials for seasonal tune-up offers.

FAQ

Furnace maintenance questions, answered

When should I schedule a furnace tune-up?

Fall, before the first real cold snap — that's when neglected furnaces fail, and when schedules fill up.

Is a furnace tune-up really necessary every year?

Yes — for safety (the CO check), for reliability, and because most manufacturers require documented annual maintenance to keep the warranty valid.

Do you tune up boilers too?

Yes — furnaces, boilers, and heat pumps, every make and model.

How long does a furnace tune-up take?

Most take an hour or two. It can take longer if we find a problem or the furnace hasn't been serviced in a while.

Can I just change the filter instead of getting a tune-up?

Changing the filter is important, but it doesn't check the heat exchanger, carbon monoxide levels, gas pressure or safety controls. Those need a technician.

Do you service brands other than Bryant?

Yes. We service every make and model of furnace, boiler and heat pump.

What if the technician finds a problem?

We show you what we found, explain the options and give you the price before doing any work. Nothing is replaced without your OK.

Ready when you are.

Free estimates and straight answers across the Twin Cities. After-hours emergency service available.