New Construction HVAC
The best HVAC system is the one designed in from the start. Heating & Cooling Two partners with builders and homeowners on new construction across the Twin Cities metro — complete system design, custom ductwork from our own sheet metal shop, and installation that passes inspection the first time. Since 1980. Call 763-428-3677.
Family-owned since 1980
Three generations of Twin Cities neighbors keeping homes and businesses comfortable.
NATE-certified technicians
Factory-trained, background-checked techs who explain the work before they start.
Bryant Factory Authorized Dealer
Top-tier equipment, factory warranties and rebates you can only get from an authorized dealer.
Scope
What we bring to a build
- Complete heating, cooling, and ventilation design
- Custom ductwork fabricated in-house — designed for the plans, not adapted after
- Furnaces, ACs, heat pumps, boilers, radiant, and geothermal
- Air exchangers and ventilation to meet code in tight new homes
- Water heaters and garage heaters
- One sub responsible for the whole comfort system
Four decades of builds
Ductwork built to the plans
We've worked with Twin Cities builders for four decades. Our residential sheet metal fabrication means the ductwork matches the architect's plans instead of compromising them — soffits stay small, runs stay short, and rooms get the airflow the load calc says they need.
On the job
New construction ductwork, installed by our own crew
Real photos from a recent new-construction job: our team hanging trunk lines, fittings and supply runs in an open-framed building before the drywall goes up.












Design first
Sizing the system from the plans
Every new home we design starts with a room-by-room heat loss and heat gain calculation from the plans. That tells us how much heating and cooling each room actually needs, which drives the size of the furnace or heat pump, the size of every duct and where each register goes. Today's tight, well-insulated homes need much less equipment than older houses of the same size. Oversized equipment short-cycles, runs loud and leaves rooms uneven.
Ventilation
Fresh air in a tight new home
Minnesota's residential energy code requires new homes to have balanced mechanical ventilation, where the air brought in is within 10 percent of the air exhausted. In practice, that usually means an air exchanger (HRV or ERV) designed with the rest of the system. We size it, plan the duct runs and set it up so the house gets fresh air without wasting heat. Learn more in air exchanger settings for a Minnesota winter.
For builders
How we work with builders
- We bid from your plans and design the complete comfort system.
- We coordinate rough-in timing around framing, plumbing and electrical.
- We fabricate ductwork in our Maple Grove shop to the plans, so it fits the framing instead of fighting it.
- We plan chases and soffits early, so ducts stay small and hidden.
- We handle heating, cooling, ventilation, water heaters, radiant and garage heat under one contract.
For homeowners
Decisions to make before the walls close
- Zoning for a two-story or a walkout basement, so each level can have its own thermostat. See thermostats and zoning.
- Radiant floor heat in the basement slab, bathrooms or garage. It has to go in before the pour. See radiant floor heating.
- A snowmelt driveway, walk or steps, planned before the concrete goes in.
- A cold-climate heat pump or geothermal system instead of gas-only heat.
- A whole-home humidifier and better filtration, built into the plans.
- A garage heater, or at least a gas line and vent location for one later.
These are much cheaper to add during construction than after. Read radiant floor heating in Minnesota homes and heated driveways and snowmelt systems.
FAQ
New construction questions, answered
Do you work with custom home builders?
Yes — custom homes, spec homes, and additions. We bid from plans and design the complete comfort system.
Why does in-house sheet metal matter for new construction?
Because stock fittings force compromises. Fabricating to the plans means better airflow, smaller chases, and fewer surprises at inspection.
Can you do radiant or geothermal in a new build?
Yes — new construction is the ideal time for both. We'll present the options with real operating-cost comparisons.
When should HVAC be planned in a new build?
As early as possible, ideally while the plans are being finished. That's when duct chases, mechanical room space and options like radiant floors are easiest and cheapest to add.
Does a new Minnesota home need an air exchanger?
Minnesota's energy code requires balanced mechanical ventilation in new homes, which is usually provided by an air exchanger (HRV or ERV).
Do you work on additions and remodels too?
Yes. We design heating and cooling for additions, finished basements and major remodels, including custom ductwork from our shop.
Ready when you are.
Free estimates and straight answers across the Twin Cities. After-hours emergency service available.
